Gel gasket: supertight, crystal clear, bubble free

We are producing high-efficient cleanroom and process air filters with gel seal. The gel seal is either made from polyurethane or silicone. It offers lowes shore hardness and always safely seal your clean enrivonment. Leak flows due to gasket aging or age induced decay of the gasket tension are virtually impossible. Our gel gaskets are free of any bubbles to prevent micro contaminations.

A classic design with many options

Usual deep-pleat separator technology reaches back into the first days of finedust and HEPA filtration. We still produce such labourious filters with aluminum or stainless separators for demanding applications such as high-temp filtration (120°C, 250°C or 380°C), explosion protection or where highest burst pressures are required. Beside this such filters can also be fitted to produce dedustable finedust and HEPA filters.

It's the folding geometry

Especially HEPA and finedustfilters that are laid out for maximum air flow or ultimate energy efficiency require folding geometrics without compromises. Our finedust, EPA, HEPA and ULPA filters are manufactured with most advanced production technologies to allow best useage of the given filtersurface under any circumstance. This is ensured for fold depths of up to 250 mm!

HS-Strongshield EX

The pioneering HS-Strongshield filter technology enables maximum media tear strength up to> 100 kPA, safe dissipation of electro-static potentials for ATEX areas, pulse cleaning dedusting up to 6 bar and filter classes up to EN 1822 H14. The ultima ratio in safe filtration solutions for demanding filter tasks.

Benutzen Sie unseren Produktfinder
▲

High efficient Particle filtration: EPA / HEPA / ULPA

Range of application
  • filtration of to separate airborne particles or particulaire air impurities down to 0,1 µm (i.e. viruses, germs, toxic dusts)
  • resistant up to 250 °C
  • clean room filtration
  • process air
  • operation room ceilings
  • Laboratories, clean work benches
  • for supply and exhaust air
HS-Particulate Filter Cells Type HS-Mikro-S are HEPA / ULPA filters, these filters are installed where the maximum of air cleanliness is demanded. This particulate filter is needed on the air intake side for the separation of suspended matters e.g. viruses, germs, toxic types of dust, aerosols etc.serve. It used e.g. in the medical area according to DIN 1946, in areas like operation rooms, intensive care units, laboratories, and in the precision technique, thus always where germ or dust free air is essential. HS-Mikro-S filters are also installed on the exhaust air side if pathogene, toxic or radioactive particles must be removed from the exhaust air.

HS-Mikro-S-Filters are available in different versions, whereby the filter media us always high-quality high efficiency and superhomogeneous glass fibre paper with different degrees of separation.

The paper is pleated and provided either with aluminum or thermoplastic separators. This arrangement of pleated fibre medium is absolutely leak free connected to the frame of the cell with an elastic non-porous grouting compound.

A higher filter surface is achieved by a special folding and the use of thermoplastic spacers than with conventional HEPA-Filters; thus there are larger flow rates with the same pressure loss and the same flow rates. The difference of pressure will be smaller at the same flow rate. Those filters have a smaller weight than those with spacers made of aluminum, which facilitates the handling enormously.

HS-V-Pak SFV and HS-V-Pak RFV

V-Form compact EPA and HEPA Filters used with mobile applications, glove boxes and clean benches.

  • 65°
  • >95
  • E11
  • H13
  • H14

These compact HEPA filters are used as mainfilters in stationary applications such as cleanroom, pharmaceutical, medical or nuclear (i.e. in gloveboxes, cleanbenches etc.). With mobile applications HS-V-Pak SFV are used in machinery and vehicles that require controlled air quality (i.e.
Waste disposal, exhaust into cleanrooms). HS-V-Pak filters are in use where less installation space or flexible arrangements are required. HS-V-Pak filters allow maximum usage available space in channel sections. HS-V-Pak SFV filters consist from fully combustible raw materials so the filter can be completely incinerated after use. This allows easy disposal especially when toxic or biohazardous filtrates are collected by the filter.

Standardsize: 86,5x202x600 mm.

Standard: Filter class H13 - H14 (HS-V-Pak SFV) or E11 (HS-V-RFV) according to EN 1822, plastic frame made from ABS

Options: foamed gasket at air entry, burst protection

HS-V-Pak SFV or HS-V-Pak RFV are temperature resistant up to appx. 65°C  and resistant for up to 100% rel. humidity.

Dataheet

HS-Mikro SF and HS-Mikro RF

EPA / HEPA for multiple clean and sterile air purposes

  • 65…120°
  • >95
  • E11
  • H13
  • H14

HEPA-Filters with minipleated micro glass fiber media and thermoplastic spacers, applicable for process protection in industry and technology as well as for sterile and cleanroom environments. A higher effective filter surface than with conventional mechanical filters is reached by a special folding geometry and the use of thermoplastic spacers. These filters are nearly metal-free and thus completely incinreable.

Standard: Filter class H13 (HS-Mikro SF) or E11 (HS-Mikro RF) in accordance with EN 1822, MDF framework and foamed non-porous seal.

Options: metal frames, special seals, div. Filter classes (E11 - U16), grasp protection, handles, flanges etc. possible.

HS-Mikro SF or HS-Mikro RF are temperature-resistant up to approx. 65°C with r.H. up to 100 %.


Datasheet

HS-Mikro S and HS-Mikro R

High efficient EPA and HEPA filters with classical aluminum spacer technology. Loads of different options are availiable.

  • 120…250°
  • >95
  • E11
  • H13
  • H14

Filtercells made from micro glass fiber media and curved aluminum spacers. Filters are versatile applicable for process protection in industry and technology. The use of aluminum spacers allows more options e.g.: cleanable filter media for up to 10.000 cleaning cycles, high temperature filters or electrical grounding for explosion protection.

Standard: Filter class H13 (HS-Mikro S) or E11 (HS-MiKro R) in accordance with. EN 1822, with MDF framework and a foamed, non-porous seal.

Options: Metal frame, special seals, div. Filter classes (E11 - U15), grasp protection, handles, grounding, flanges, dedustable filter media, high temperature filters (to 250°C), etc. possible.

HS-Mikro S or HS-Mikro R are temperature resistant to approx. 120°C or 250°C with r.H. up to 100 %

Datasheet

HS-Mikro SFV and HS-Mikro RFV

EPA and HEPA filter with maximum filtersurface for highest airflow / lowest pressure drop.

  • 65…120°
  • >95
  • E11
  • H13
  • H14

Filtercells made from minipleated micro glass fiber media and thermoplastic spacers. The filter cartridges are arranged in V-shapes to attain a higher filter surface and thus higher airflow rates with lowest possible pressure drop. Versatile applicable for process protection in industry and technology as well as for sterile and clean room environments. These filters are nearly metal-free and thus completely incinreable.

Standard: Filter class H13 (HS-Mikro SFV) or E11 (HS-Mikro RFV) in accordance with. EN 1822, with MDF framework and a foamed non-porous seal.

Options: Metal frames, special seals, div. Filter classes (E11 - U16), grasp protection, handles etc. possible. HS micro SFV or HS-Mikro RFV are temperature resistant up to approx. 65°C with r.H. up to 100 %.

Datasheet

HS-Mikro SF-AL and HS-Mikro RF-AL

Laminar Flow Filter for clean rooms, clean benches, FFU's and operational theatres.

  • 65…120°
  • >95
  • E11
  • H13
  • H14
  • U15
  • U16
  • U17

These HEPA and ULPA filter elements are employed for the highest requirements in the range of the cleand and sterile room environments like clean work benches and for installation in operating room ceilings. The filtercells consist of minipleated micro glass fiber media with thermoplastic spacers. The framework consists of sturdy extruded and andonised aluminum. The optimal folding geometry guarantees a laminar air flow in the work area. So there is no need for laminator insets or similar aids.

Standard: Filter class H14 (HS-Mikro SF-AL) or E11 (HS-Mikro RF-AL) in accordance with. EN 1822, andonised extruded aluminum framework and foamed non-porous seal, one-sided powder-coated grasp protection.

Options: Special seals (i.e. jelly seal) , div. Filter classes (E11 - U17), two sided grasp protection, flanges, etc.

HS-Mikro SF-AL or HS-Mikro RF-AL are temperature resistant up to approx. 65°C with a r.H. up to 100 %.

Datasheet

HS-Mikro Pak SFV and HS-Mikro Pak RFV

Compact filter as to be used as alternative for enhancing or substitution of existing finedustfilterstages in existing filtersystems.

  • 65°
  • >95
  • E11
  • H13

HS-Mikro Pak SFV fits idealy as main filter stage where high air flow rates and maximum efficiency are required. HS-Mikro Pak SFV are applied mainly in industrial process (i.e. as safety filter after mechanical oil-fog filters). HS-Mikro Pak SFV also fit as mainfilterstage for the removal of particles, toxic dusts or aerosols from the exhaust or supply air flows, especially when
high flow rates are required. The V-bank system offers superior filter surfaces and therefore ensures a longer service lifetime. The filterframe offers maximum rigidity and is corrosion free. It is consisting of plastic and therefore guarantees an easy waste disposal because the whole filter is completely incinreable.

Standard: Filterclass H13 (HS-Mikro Pak SFV) or E11 (HS-Mikro RFV) according to EN 1822, plastic frame, circulating 25 mm flange on face side

Options: foamed gasket on the flange, burst protection grid

HS-Mikro Pak SFV and HS-Mikro Pak RFV are temperature resistant up to 65°C @ r.H. up to 100 %.

Datasheet

HS-Deka Pak SFV bzw. HS-Deka Pak RFV

Low energy consuming compact filter, serving as high efficient alternative to substitute finedustfilters for efficiency boosting in exsisting filter systems.

  • 65°
  • >95
  • E11
  • H13

HS-Deka Pak SFV EPA and HEPA filters provide twice the filter area compared to conventional types of rigid bag HEPA filters due to the greater depth of 420 mm. This allows for applications such as turbo machinery, process air and hygiene HVAC maximum flow rates and significantly longer service life. HS-Deka Pak SFV are especially recommended for applications where installation space is critical but high flow rates are required. Due to the tolerance against high air speed this filter gives more freedom in the design of space saving filter processes. HS-Deka Pak suit ideally as pre- or main filter for filtration of particles and aerosols. They serve as intake and exhaust air filter also in harsh operating environments with high humidity. The sturdy plastic frame is corrosion-free and allows for easy disposal, since the filter can be completely incinerated after ending its service lifetime. Existing bagfilterstages can be easily upgraded by exchange due to the fact that HS-Deka Pak SFV fit into standard bag filter mounting frames.

Standard: Class H13 (HS-Deka Pak SFV) or E11 (HS-Deka RFV) gem. EN 1822, Kunststoffrahmen aus Polystyrol, umlaufender, einseitiger 25 mm Flansch

Options: foamed gasket on the frame,burst protection grid

HS-Deka Pak SFV resp. HS-Deka Pak RFV are Temperature resistant up to 65°C /rel. air humidity up ot 100 %.

Datasheet

HS-Mikroseal JG

Pressure relief filter for over- / underpressure regulation at tanks, gloveboxes and safetyhousings.

  • 65°
  • >95
  • E11
  • H13
  • H14

HS-Mikroseal JG can be flexibly used everywhere, where smallest installation size combined with moderate airflows is demanded. The cartridge is not requiring a own filterhousing and can be easily attached to common pipes or tanks by the standard 1"-thread. The filtermedia is safely protected by a corrosion resistand stainless-steel frame. Among the numerous possible applications the cartridge servs mainly as pressure relief filter at safety relevant filterunits (i.e.  HS-S04, HS-Securesorb).

Standard :  EN1822 H13, Frame stainless 1.4301, 1"-thread made from brass

Datasheet

HS-Mikroseal JG-S

Filtercartridge for the use in pipes and tubes for up to +- 300 mbar

  • 65°
  • >95
  • E11
  • H13
  • H14
  • U15

 HS Mikroseal JG-S can be applied anywhere in systems where small form factors are required at moderate volume flows. The filter cartridge does not require a separate housing and can host on/in the usual pipes and tanks. The standardized 1"-thread connector allows fast and simple fixation. The filtermedia is protected by a corrosionresistant stainless steel frame and thereby protected from external influences. The corpus is gastight sealed and allows operation within pressurized ductworks up to +- 300 mbar.
Among the numerous applications, these filters essentially serve as pressure relief filters at security relevant filter housings (eg HS-S041, HS-Securesorb) or to have controlled air exchange with pipes and tanks.

Standard:  EN1822 H13, Frame stainless 1.4301, 1"-thread made from brass

Datasheet

HS-Strongshield SF-EX H13

Dedustable HEPA safety filter for maximum stress loads, conforms ATEX.

  • -40…120°
  • F9
  • 60…95
  • H13

HS-Strongshield Filters offer the maximum security at processes with high hazard risk potentials. The groundbreaking HS-Strongshield filter technology provides a superior media tensile strength up to 400% higher than usual glass media. Different to usual Filters the HS-Strongshield filtermedia is armored by rigid layers of polyester. This ensures that HS-Strongshield filters offer an unmatched safety at extreme conditions such as high moisture, shock pressures, accident failures of pre-filterstages, presence of explosive atmospheres etc.. The air entry side of the filters is metalized and conductive to depleat any electrical potentials that can cause ignitions by grounding connectors on the filter. Hence HS-Strongshield filters ideally suit the safety needs of processes in ATEX areas. No additional protective grids are required due to the robust media structure.

HS-Strongshield filters are dedustable by typical pulsejet or blast systems.

Datasheet

l
 Contacts
 Contacts